Digilent

Eclypse Z7

Zynq-7000 SoC Development Board with SYZYGY-compatible Expansion

Contact Our Expert

Get a Quote

Zynq-7000 APSoC

Chip number: XC7Z020-1CLG484C
667 MHz dual-core Cortex-A9 processor
DDR3L memory controller with 8 DMA channels and 4 High Performance AXI3 Slave ports
High-bandwidth peripheral controllers: 1G Ethernet, USB 2.0, SDIO
Low-bandwidth peripheral controllers: SPI, UART, CAN, I2C
Programmable from JTAG, Quad-SPI flash, and microSD card
Programmable logic equivalent to Artix-7 FPGA

Memory

1 GiB DDR3L with 32-bit bus @ 1066 MT/s
16 MB Quad-SPI Flash with a factory-programmed 48-bit globally unique EUI-48/64™ compatible identifier
microSD card slot

Power

Powered from external 12V 5A supply
Platform MCU for configuration of adjustable power supplies and temperature management

USB and Ethernet

Gigabit Ethernet PHY
USB-JTAG programming circuitry
USB-UART bridge
USB micro AB port with USB 2.0 PHY with Host/Device/OTG capabilities

Zmod Ports

2 ports following the SYZYGY Standard interface specification
Compatible with a variety of SYZYGY pods, allowing for a wide variety of applications
Dedicated differential clocks for input and output
8 differential I/Os per port
16 single-ended I/Os per port
DNA interfaces connected to Platform MCU allowing for various auto-negotiated power supply configurations
Supports the Digilent Zmod AWG 1411, Scope 1410, Scope 1210, and Scope 1010

Pmod Ports

2 twelve-pin ports for a total of 16 FPGA-connected I/Os
High speed voltage translation and protection circuitry

User GPIO

2 push-buttons
2 RGB LEDs

The Eclypse Z7 is specifically designed to enable the rapid prototyping and development of embedded measurement systems. Featuring high-speed Zmod ports for modular expansion and a Xilinx Zynq®-7020 SoC, the Eclypse Z7 is fast and flexible, reducing the time it takes for engineers and researchers to develop innovative and powerful new high-speed instrumentation, control, and measurement systems for edge-computing, medical, and communications applications.

Zmod Expansion

Zmod is Digilent’s expansion solution using the open-source SYZYGY standard from Opal Kelly. Faster than the Pmod Standard and more compact and cost-effective than FMC, Zmods improve the customizability options for high-speed I/O. Plug in your application specific Zmods and get up and running in hours or days, instead of weeks or months. Take a look at the Features tab for a list of compatible Zmods.

Eclypse Z7

Artix-7 FPGA Development Board with SYZYGY-compatible Expansion

Eclypse Z7

Trainer Board for Multimedia Applications

Eclypse Z7

ARM/FPGA SoC Development Board

Eclypse Z7

Zynq Ultrascale+ MPSoC Development Board

Eclypse Z7

Zynq-7000 Single Core for ARM/FPGA SoC Development

Eclypse Z7

Breadboardable Artix-7 FPGA Module

Eclypse Z7

Kintex-7 FPGA Development Board

Eclypse Z7

Zynq-7000 SoC Development Board

Eclypse Z7

Zynq-7000 ARM/FPGA SoC Development Board

Eclypse Z7

Breadboardable Spartan-7 FPGA Module

Eclypse Z7

Spartan-7 FPGA Development Board

Eclypse Z7

Python Productivity for Zynq-7000 ARM/FPGA SoC

To create and modify designs for your Eclypse Z7, you can use Xilinx's Vivado Design Suite. Vivado is software designed for the synthesis, implementation, and analysis of HDL designs. The Eclypse Z7 is supported by the free WebPACK edition.

You can use Xilinx's PetaLinux Tools to customize, build, and deploy Embedded Linux solutions on the Zynq-7000.

Xilinx SDK enables development of embedded software applications targeting Xilinx SoC devices, such as the Zynq-7000.

System Boards

Kumpulan Abex Sdn Bhd

Digilent

Eclypse Z7

System Boards